The Arithmetic Logic Unit (ALU) is a vital hardware component of any digital computer. It is used to perform arithmetical and logical
operations, such as addition, subtraction, incrementing, decrementing and bitwise-comparison. The ALU is typically contained within CPU
chips, although it can be a dedicated piece of hardware, such as in the case where high speed number crunching is required.
Microprocessors have one or more registers called accumulators or general registers, whereby data from these registers is loaded to and
from the ALU when carrying out operations.

The basic module used in arithmetic elements is the half-adder. Its function is to add two binary digits or bits *A* and *B*,
producing the sum *S* and carry *C* bits. Respectively the sum has an “Exclusive-Or” relationship, and the carry has an “And”
relationship between its addend input *A* and augend input *B*. By itself the half-adder is not very useful as it can only add
two bits of data.

\( \begin{align}
S = (\overline A \wedge B) \vee (A \wedge \overline B) \\
C = A \wedge B \\
\end{align} \)

The full-adder can be can be constructed by combining two half-adders with an “Or” gate. Unlike the half-adder, the full-adder is able
to handle carries from other binary digit stages. Constructing a full-adder from two half-adders is not the most efficient use of
logic gates, but it does serve to illustrate the modularity of the half-adder. Notice we now have a carry-in bit, *Ci*.

\( \begin{align}
S = (Ci \wedge \overline A \wedge \overline B) \vee (\overline Ci \wedge \overline A \wedge B) \vee (\overline Ci \wedge A \wedge \overline B) \vee (Ci \wedge A \wedge B) \\
Co = (Ci \wedge B) \vee (Ci \wedge A) \vee (A \wedge B) \\
\end{align} \)

This notion of modularity can be extended by combining multiple full-adders to form a parallel-adder. The figure shows a 4-bit
parallel-adder capable of adding two 4-bit binary integers. The addend input lines labelled *A0-A3* and the augend input lines
labelled *B0-B3*, and with the addition result appearing on output lines *S0-S3*.

The parallel-adder is also capable of performing the subtraction. This is achieved by inverting the subtrahend input lines *B0-B3*
and setting the input Add/Sub bit high, which has the effect of taking the 2’s-complement of the subtrahend. When the subtrahend is added
to the minuend input lines *A0-A3*, the subtraction result appears on the output lines *S0-S3*. If the output sign bit is
high then the result is positive, if the sign bit is low, then the two’s complement of the output lines *S0-S3* will be the result
and it is negative.

There is no limit to the number of full-adders that can be cascaded. However there is an obvious delay in the circuit, as the carry
propagates through each binary adder. This delay propagation is called the “carry-ripple problem”. A common technique to alleviate this
problem can be achieved by using a “carry-look-ahead” circuit.

\( \begin{align}
S = A + B \\
\end{align} \)

The SN74181 is a 4-bit binary Transistor-Transistor-Logic (TTL) integrated circuit in the 24-pin Dual-In-Line Package (DIP), originally
manufactured by Texas Instruments in March 1970. This ALU chip was considered a breakthrough at the time and consequently used in mini
computers of the time such as the DEC PDP-11, the DEC VAX 11/780 and the Xerox Alto. The 74181 provides multi-level carry look-ahead
circuitry to minimise the carry-ripple problem. Without this circuitry, delay propagation issues would have been a problem especially as
eight 74181 were cascaded in the case of the VAX11/780 32-bit machine.

The 74181 is able to perform a variety of arithmetical or logical operations depending on the logic state of input pin *M*
(L = logical, H = arithmetic).

These 74181 chips are getting harder to find since they have not been manufactured since 1994, having been rendered obsolete by modern
microprocessors and microcontrollers having their own internal ALU. However by looking hard enough it is still possible to find sources
of new old stock samples for experimentation purposes.

The photo shows a 74181 wired up to a breadboard with some LEDs and DIP switches. Observe that the DIP switches positions have put
the 74181 into arithmetic mode (*M* = L, *S0* = H, *S1* = L, *S2* = L, *S3* = H). Since the 74181 expects
the 4-bit input words to be inverted, setting *Cn* = H compensates for this. The binary digit of 2 is being applied to addend
input lines *A0-A3*, and the binary digit of 10 is being applied to the augend input lines *B0-B3*, which results in an
output result of 12 (*F0* = L, *F1* = L, *F2* = H, *F3* = H). Showing that two plus ten does in fact equal twelve.

If it is not possible to source a 74181 for experimentation purposes, all is not lost as there is an excellent digital logic designer
aptly name Digital. This tool is described as an easy-to-use digital logic designer and circuit simulator designed for educational
purposes.

The figure here shows a Digital simulation of the above breadboard circuit. Notice that the input DIP switch settings from the
breadboard circuit have been transferred to the simulation. After running the simulation, reassuringly the same output LEDs as the
real-life breadboard circuit are illuminated.

This website is powered using ultra low power green locally based servers.

Copyright © i4cy 2000-2021. All rights reserved.